Charging Station Test Adapter Kit With Type 2 Connector
You may service and test EV Chargers installed in public and commercial places for electrical safety and compliance with AS3000 standards with this equipment for testing electric car charging stations. You may thoroughly test any charging station with the EVSE adaptor.
- Testing for potentially harmful voltage against earth on PE conductor is possible.
- Use the PP State rotary switch to simulate the current capability of charging cables when performing cable simulation.
- Perform testing of various charging states using vehicle simulation.
- Make a PE error (Earth fault) simulation
- Test in accordance with IEC/EN 61851-1 and IEC/HD 60364-7-722
With the help of this electric vehicle charging station testing equipment, you can inspect and assess the electrical safety and AS3000 compliance of EV Chargers installed in public and commercial spaces. With the EVSE adapter, you can thoroughly test any charging station.
Inclusions:
- Instrument
- Soft Carrying Bag
- Instruction Manual
The FEV300 test adapter kit with a Type 2 connector is made to assess the efficiency and security of charging stations using AC in mode 3. An installation tester (Fluke 1664 FC) and/or a ScopeMeter® (Fluke 120B Series) are two suitable test instruments that can be used in conjunction with the adapter to conduct testing while it simulates an electric vehicle and initiates a charging cycle. Charging stations can be tested in compliance with IEC/EN 61851-1 and IEC/HD 60364-7-722 using the adapter kit.
Application:
- On-site evaluation of the EVSE charging station setup.
- Private, semi-private, and public EVSE charging stations have undergone initial and ongoing testing.
Functions:
- PE Pre-Test Visible indication >50 V AC/DC between PE conductor and touch sensor
- PP Simulation Open, 13 A, 20 A, 32 A, 63 A
- CP States State A, B, C, D
- CP Error state “E” On/off (CP signal short-circuited to PE)
- PE Error state “F” (Earth fault) On/off (interruption of PE conductor)
- Outputs (for test purpose only)
- Measuring terminals L1, L2, L3, N, PE Max. 250/480 V, max. 10 A
- CP signal output terminals Approx. +/-12 V
- Caution: In case of wrong wiring or error of the charging station these terminals may be hazardous.
Use the FEV300-CON-TY2 Type 2 Plug to connect to an EV charging station Type 2 with a socket outlet or an EV charging station Type 2 with a vehicle connector. All in one adapter that safely interfaces with the Fluke array of test and measurement tools to perform a variety of tests such as ground fault checks, wire insulation, measuring voltage and duty cycle to see maximum current available for charging. The FEV300 can mimic CP (E) and PE (Earth Fault) errors and features independent phase indication through three LED lamps for a quick check to see if voltage is present. There is no need to bring an electric vehicle onsite for charging station troubleshooting: when connected to a charging station, the adapter functions as an electric vehicle for convenient performance and maintenance testing.
General features:
- Input voltage – Up to 250 V (single phase system) / up to 480 V (three phase system), 50/60 Hz, max 10 A
- Internal power consumption – 3 W max.
- FEV300-CON-TY2 Plug AC charging mode 3, suitable to IEC 62196-2 type 2 socket outlet or fixed cable with vehicle connector (type 2, 7P three-phase)
- Dimensions (H × W × D) 110 × 45 × 220 mm length without connection cable and test cable
- Weight – Approx. 1 kg
- Safety standards IEC/EN 61010-1, pollution degree 2
- IEC/EN 61010-2-030, CAT II 300 V, protection class II
- Ingress protection IEC 60529: IP54 (housing)
- IEC 60529: IP54 (sockets with protection caps in place, connectors in connected condition or with protection caps in place, otherwise IP20)
- Operating temperature -20 °C to 40 °C
- Storage temperature -20 °C to 50 °C
- Operating humidity range 10 % to 85 % relative humidity non-condensing
- Storage relative humidity 0 % to 85 % non-condensing
- Operating altitude 2000 m max.